Milan Technology Switch MIL S1600S User Manual

MIL-S1600S  
User’s Guide  
The MIL-S1600S switch is a sixteen port switch that can be used to  
build high-performance switched workgroup networks. This switch is  
a store-and-forward device that offers low latency for high-speed net-  
working. The MIL-S1600S switch has 16 auto-sensing 10/100Base-  
TX RJ-45 ports with auto MDI/MDIX and features a "store-and-for-  
ward " switching scheme. This allows the switch to auto-learn and  
store source address on an 8K-entry MAC address table. Auto  
MDI/MDIX allows connection to another switch or workstation without  
changing non-crossover or crossover cabling.  
1
 
Troubleshooting  
Features  
• Conforms to 802.3, 802.3u, and 802.3x standard.  
• 16 auto-sensing 10/100Mbps Ethernet RJ-45 ports.  
• Automatic MDI/MDIX crossover for 10Base-T and 100Base-TX  
ports.  
This section is intended to help you solve the most common prob-  
lems on the MIL-S1600S switch.  
Incorrect connections  
• Auto-negotiation supported.  
• Back-Pressure-Base flow control on Half-duplex ports.  
• Pause-Frame-Base flow control on Full-duplex ports.  
• Store-and-forwarding switching architecture for abnormal packet fil-  
tering.  
Faulty or loose cables  
Look for loose or obviously faulty connections. If they  
appear to be OK, make sure the connections are snug. If  
that does not correct the problem, try a different cable.  
• Full wire speed forwarding rate.  
• 8K-entry MAC address table.  
• LED-indicators for Power, Link/Active.  
Non-standard cables  
Non-standard and miswired cables may cause numerous  
network collisions and other network problem, and can  
seriously impair network performance. A category 5 cable  
tester is a recommended tool for every 100Base-T network  
installation.  
Package Contents  
Unpack the contents of the MIL-S1600S switch and verify them  
against the checklist below.  
Improper Network Topologies  
It is important to make sure that you have a valid network  
topology. You should make sure that your network topolo-  
gy contains no data path loops. Between any two-end  
nodes, there should be only one active cabling path at any  
time. Data path loops will cause broadcast storms that will  
severely impact your network performance.  
• MIL-S1600S switch  
• Power Cord  
• User Guide  
Diagnosing LED Indicators  
The switch can be easily monitored through panel indicators to assist  
in identifying problems, which describes common problems you may  
encounter and where you can find possible solutions.  
If the power indicator does not turn on when the power cord is  
plugged in, you may have a problem with power cord. Check for  
loose power connections, power losses or surges at power outlet. If  
you still cannot resolve the problem, contact your local dealer for  
assistance.  
Compare the contents of your MIL-S1600S switch package with the  
standard checklist above. If any item is missing or damaged, please  
contact your local dealer for service.  
6
3
 
Rear Panel  
Hardware Description  
The 3-pronged power plug is located at the rear Panel of the MIL-  
S1600S switch as shown in Figure 2-2. The switch will work with AC  
in the range 100-240V AC, 50-60Hz  
Front Panel  
The Front Panel of the MIL-S1600S switch consists of 16  
10/100Base-TX RJ-45 ports The LED Indicators are also located on  
the front panel of the switch.  
Desktop Installation  
RJ-45 Ports (Auto MDI/MDIX): 16 10/100 auto-sensing for  
10Base-T or 100Base-TX connections. (In general, MDI means con-  
necting to another hub or switch while MDIX means connecting to a  
workstation or PC. Therefore, auto MDI/MDIX means that you can  
connect to another switch or workstation without changing non-  
crossover or crossover cabling.)  
Set the switch on a sufficiently large flat space with a power outlet  
nearby. The surface where you put your switch should be clean,  
smooth, level and sturdy. Make sure there is enough clearance  
around the switch to allow attachment of cables, power cord and  
allow air circulation.  
Power ON  
LEDs Indicators  
The LED Indicators gives real-time information of systematic opera-  
tion status. The following table provides descriptions of LED status  
and their meaning.  
Connect the power cord to the power socket on the rear panel of the  
switch. The internal power supply in the switch works with AC in the  
voltage range 100-240VAC, frequency 50~60Hz.  
LED  
Status  
Green  
Off  
Description  
Check the power indicator on the front panel to see if power is prop-  
erly supplied.  
Power  
Power On  
Power is not connected  
LK/ACT  
Green  
The port is connected with  
operating device.  
Blinks  
Off  
The port is receiving or  
transmitting data.  
No device attached.  
4
5
 

Musica Portable Speaker 6C User Manual
NEC Car Video System X401S User Manual
Nextar Calculator D3201 User Manual
Northern Industrial Tools Air Compressor 1 HP 16 GALLON AIR COMPRESSOR User Manual
Numark Industries Musical Instrument DM1685 User Manual
Oki Printer 58374501 User Manual
Panasonic Switch AW SW350E User Manual
Panasonic Vacuum Cleaner MC CG983 User Manual
Panasonic VCR AJ D250P User Manual
Patton electronic Network Router 07MSN5300 QS User Manual